Search found 7 matches
- Wed May 28, 2014 6:59 pm
- Forum: Installation
- Topic: TPS works with engine off, but no TPS signal with engine on
- Replies: 1
- Views: 3469
TPS works with engine off, but no TPS signal with engine on
Hi, My MJLJ v3 instalation have now been running flawless for I guess around 6years. But lately I have noted that I really don't have the power as I used to have and the throttle control is horrible at low RPM. :( I have spend the last couple of months trying to get my mac to connect to the MJLJ, bu...
- Thu Sep 05, 2013 6:57 am
- Forum: Operation
- Topic: cuts out at high RPM
- Replies: 2
- Views: 4532
cuts out at high RPM
I have now been running flawlessly with the megejolt for 5 years on my 1968 Lotus Super Seven. But I'm starting to experiece some problems. When hot and accelerating hard, the ignition cuts completely for a few (2-5) seconds, and then continues normally after that. The hotter the worse. Dosent sound...
- Mon Mar 08, 2010 12:14 pm
- Forum: Installation
- Topic: The rev counter issue
- Replies: 6
- Views: 8206
I'll try to kill the Zener.
also I found this one http://www.autosportlabs.org/viewtopic. ... r&start=30 looks very much like my scenario and suggests to wire the rev counter directly to the PIP signal.
/jano
also I found this one http://www.autosportlabs.org/viewtopic. ... r&start=30 looks very much like my scenario and suggests to wire the rev counter directly to the PIP signal.
/jano
- Sun Mar 07, 2010 12:21 pm
- Forum: Installation
- Topic: The rev counter issue
- Replies: 6
- Views: 8206
The rev counter issue
I have a SMITH RVC rev counter that I'm trying to get working with megajolt. I have built the suggested circut with the zeners and even purchased the prebuild thingy from triggerwheels, but I can't get it to work. When the engine is at idle, the rev counter shows about 1500 rpm, but when increesing ...
- Thu Jun 19, 2008 12:24 pm
- Forum: Installation
- Topic: Glue or weld?
- Replies: 11
- Views: 18089
balanced
Balance is important, you can certainly feel the missing tooth when the trigger wheel is spinning 6000+ rpm My trigger wheels is bolted on the pully with a single center bolt. I have balanced the the trigger wheel with a 4mm screw, the screw also acts as a fixing point going into a grove I have made...
- Fri Jan 05, 2007 6:38 pm
- Forum: Assembly
- Topic: Free Molex connectors.... no problems!
- Replies: 4
- Views: 6205
Free Molex connectors.... no problems!
Hi Just recieved my MJLJ today. I was worried about the availability of the Molex connector, but there is no problem with that at all. 1) Brent had included a molex connector :-) 2) The molex connector is the same as the connector (22 pin) you find on a normal PC power supply! All you need to do is ...
- Tue Dec 26, 2006 4:29 pm
- Forum: Powered by Megajolt Gallery
- Topic: Installed no probs on ford crossflow (x-flow)
- Replies: 12
- Views: 19281
map for xflow with 244 cams
Hi
I have a kent 244 cammed Xflow engine with forged pistons.
Any one got a map that they would share with me?
/jano
jan@janolesen.com
I have a kent 244 cammed Xflow engine with forged pistons.
Any one got a map that they would share with me?
/jano
jan@janolesen.com