Autosport Labs

Once again thank you Brent.

seems the connector on the EDIS module is a little iffy and had some green corrosion in it, pulled the oins out and cleaned them up and all is ok.

the red locking tab is a little week so i will try and get another.

thanks again

Grant

Thank you for the reply Brent.

I am sure polarity is ok and as mentioned when i start to crank i have signal, while still cranking and after a second or two signal is cutting out, i tried polarity just encase and i got no tacho pulse at all.

I will go over all signals again.

Thanks

Grant

Thanks for that, but i have not moved the sensor since it was running, i will see if if can get my hands on another sensor for testing with.

I have a feeling it has to be somthing i have done with moving my wiring around, just weird why i get a pulse and then it stops.

thanks

Grant

dropping crank angle signal  Hi Guys, looking for some help. not sure what i may have done here but my car was running fine and i fitted a new coolant temp gauge and re-routed the crank sensor wiring to clean up the wiring. now the bugger will not start... when i turn ignition on and start cranking ...

Hi all, My V2 MJJL has operated faultless since i installed 4+ years ago. i am looking to upgrade to the new V3 kit. can anyone give me good advise on the major benefits etc? is the molex connector different? what about coil and CAS sensor do they require upgrade and connector changes or is the whol...

Hi all, I have my VR sensor lined up on the 9th tooth from the missing tooth on my EDIS4 system and car runs great. however when i put my timing light on the car and set the MJLJ to 0 and using my snap on timing light scroll to "0" to see how close i have the point for my sensor i am right...

Hi Guys, My mini (1.3 turbo setup) had a bit of a missfire even under light throttle but when RPM got to about 3,000 the ignition would just drop out and the tacho would read 0. I worked out the VR sensor was too far away from the trigger wheel and then the rpm was fast enough the sensor was not get...

Ok, So i fitted Resistor plugs and swapped to my original cable and it works, however it does occasionally lock up, but i think it is the PC not the MJLJ software. Thanks for all your help guys (especially Brent) it is appreciated, this Forum is one of if not the best for getting clear and great hel...

I am using BP7ES plugs and have done for ages with the MJLJ.
I will try resistor plugs tonight.

just dont understand as it all used to work ok, that is why i think it could be the laptop.


thanks

Grant

well no luck, same thing all ok while engine is not running, can adjust anything and everything for long periods of time, played for 10 mins minimmum. as soon as i started the car 5 or seconds and bam froze MJLJ program, would not restor communication and had to reboot PC twice before it would work ...

Ok soooo this could be very spot on, as i have just put the motor back in the car to just get it running to ensure all is well before i put the engine on the engine dyno etc and i have not mounted the MJLJ ECU in its normal place as i was to put it all back out again for Dyno, s it is only sitting o...

thanks for the feedback as always Brent, SO i have swapped cables and updated the graphics card but still no luck, I have never used this old laptop on the car before, lets call it (PC1), i got this as a second hand unit, so i thought i would try my work laptop (call it PC2) it is on Windows 7 and i...

Hi all, I have my car running, now to cut a long story short, i have done a full engine rebuild (mini turbo A series) and for the MJLJ the onlt chance is a new bracket for the crank sensor (same spot as before) now i am using a different laptop than previously and for some reason after around 5 seco...

OK I HAVE SUCCESS

it looks like i had a dud USB in my laptop.

I removed and reinstalled the driver and operation is now perfect.

thank you very for your help Ryan

Hi Ryan, I have tested all the 5v supplies and all are ok and i have 12v at the last point (as i am using a jumper pack. So does that mean it is a PC problem? I have contacted a mate who's PC connects to his V4 unit, i am heading over there in a few nights time to use his PC and see if my unit will ...