Autosport Labs

Hi there can anyone point me in the right direction with this please. I require help with the internal wiring on my V3 board. I've soldered wires onto the Hard cut board Coil , +12 , Trig, Gnd. http://i169.photobucket.com/albums/u210/spunkysimon/v3Hardcut.jpg But where do I connect / patch into the ...

Brent you are not wrong mate.

I followed your instructions and hay presto we're all systems go.

So, tomorrow will be start-up day.

Thanks again

Teds

Right I think I've found my fault and corrected it. But now when I turn on the megajolt and try and connect to the PC. I get the following error. Unsupported controller version. MJLJ controller version 3.2.1 is not supported by this configurator.Please use a compatible version of MJLJ configurator, ...

Thanks Brent,

Fast response as usual...

I'll re-examine my work as you suggest. Hopefully this will highlight my error. I’m still learning but enjoying it on the way.

Thanks again

Teds

Hi there need some help. I've got to the point at which I'm trying to connect everything up. e.g Laptop has software on, Cable checked, Edis system wired up and in place. Thought I'd power the thing up insitue in the car. And can't seem to connect to megajolt.So checked the power again to megajolt a...

Cracking build mate. What plugs are you using? and did you have to machine the head to get the plugs to reach the chambers?

Intersting project, I had the same job with my mini using a 48 IDA. No brackets available for mounting TPS. Took 3 goes to get it right. But happy with the results. Much cleaner install.

Nice Job.

Teds

As MartinM say's bolted onto the carb. Theres thousands of fiesta's out there for the taking. Also, you can strip the whole EDIS system off in a one'er. If you do that, re-installing into its new home is much easier. And make sure you do the same for the TPS including the 3 pin plug. Teds. P.S. Sorr...

Here's the TPS sensor in question... http://i169.photobucket.com/albums/u210/spunkysimon/DSC00684.jpg http://i169.photobucket.com/albums/u210/spunkysimon/DSC00681.jpg I'll let you how and if it all works out. Came of a 1990 mk2 fiesta. As did all the rest of my Edis system. This is its intended new ...

I've tested the tps as you described and my results are- Red seems to be the centre. Green = high res, Yellow = low res. And green and yellow decrease and increase accordingly when the lever is operated. So from this can you guys indicted to me what’s what. My guess is. E.g. Red = signal Green = +5v...

Thanks brentb.

Thats sounds like a plan, I thought there would be a better way than just using guesswork.

Once these are connected it's start up time.

Thanks again

Teds

Hi there, I have 2 Weber TPS units acquired from 2 separate ford fiestas. 1990.ish, ( number on units are PF07/03. )And, they have 3 wires which return to a 3 pin plug. Which are Red,Green,Yellow. Is there any way of identifying these wires. For Ground, Signal, Live. Hope you can help. Cheers Ted

Kit came form the main man Brent. Thought it fit that my money goes direct to the man who's done all hard work and development.

So I should be on to a winner!

Thanks MartinM for clarifying things.

Teds

Phew...! That’s a relief. Because being the impatient type I’ve already made up the cable. Thanks for confirming things. My only other question is, are the chips which are supplied already loaded up with the boot up info. In other words will I be up and running or do I need to upload stuff before it...

Hi there, I’ve just built up my board and noticed that on the schematic drawings, that with the rs232 female connector on the board only uses pins 2, 3 which communicate with the board and pins 5, 9 go to earth. So my question is, if I just mirror this pin connection pattern within rs232 cable every...