Search found 16 matches

by sandersk
Sun Apr 16, 2006 9:06 am
Forum: Future Upgrades
Topic: Switching between maps on the fly
Replies: 6
Views: 7491

Switching between maps on the fly

Hi folks, this new feature is overwhelmingly the most popular request on the Poll, just wondered if anyone is doing any work in this area???

Keith
by sandersk
Fri Nov 11, 2005 7:44 pm
Forum: Installation
Topic: unable to connect to controller
Replies: 3
Views: 4678

Are you using USB/Serial adaptor?

I tried using a cheap USB/Serial adaptor and had similar problems. Borrowed a Belkin, removed/added everything again and eventually got it to work after lots of struggling and disabling internal modem etc etc. If you can borrow laptop with "real" COM port then suggest trying this first to ...
by sandersk
Fri Nov 04, 2005 9:05 pm
Forum: Operation
Topic: EDIS wont advance - no SAW output
Replies: 12
Views: 9550

Confession time.....

Well I've finally found the problem that's been bugging me for ages and YES it was something very simple in the end. In my infinite wisdom, for some reason that will now give me global international embarassment, I goofed on the wiring, well not exactly the wiring but the SCREENING! I'd conected con...
by sandersk
Fri Oct 28, 2005 10:58 am
Forum: Operation
Topic: EDIS wont advance - no SAW output
Replies: 12
Views: 9550

Sounds about right

Thank you for your suggestions. Those scope readings sound very similar to what we observed so helps confirm that MJ is probably working correctly. I plan to confirm that my EDIS units are ok by trying them in friends car this weekend. Have already buzzed-out the wiring and that's ok so will look mo...
by sandersk
Thu Oct 27, 2005 6:37 pm
Forum: Operation
Topic: EDIS wont advance - no SAW output
Replies: 12
Views: 9550

Still no Advance!!

I'm still plugging away but getting the feeling I'm just digging a big hole! Summary: No advance seen with strobe Software ok and seeing runtime display Tach output works (although stops at 2700rpm due to pulse width I guess - the least of my problems at the moment) Seeing small a.c. voltage on SAW ...
by sandersk
Mon Oct 17, 2005 7:23 pm
Forum: Operation
Topic: EDIS wont advance - no SAW output
Replies: 12
Views: 9550

Pin 13 reading 0.1v - 0.25v

Brent,
On Pin 13 getting 0.1v at tickover rising to 0.25 at mid-revs. This seems low to me. Also checked with meter from Pin 13 to SAW on Molex - measured 100ohm as I would expect.

Does this mean I've got a duff Processor?

(odd that I'm getting tach output though!)


Keith S.
by sandersk
Fri Oct 14, 2005 7:02 pm
Forum: Operation
Topic: EDIS wont advance - no SAW output
Replies: 12
Views: 9550

Have tried some of that...

Thanks Martin and Brent for your suggestions, I'm competing off-road this weekend so re-fitted dizzy for now and will resume diagnostics Monday evening. However I've already checked.... Software comms ok Realtime display ok PIP ok (at Molex) No SAW (at Molex or Board or nearest resistor) 12v, 5v and...
by sandersk
Thu Oct 13, 2005 4:45 pm
Forum: Operation
Topic: EDIS wont advance - no SAW output
Replies: 12
Views: 9550

EDIS wont advance - no SAW output

Hi,
Had MJ fitted less than a week. Noticed drop in performance and found that there's no SAW output from MJ. There are no visible dry joints or similar so concluding that a component has failed.

Please help me if you can as I'm struggling :-(

Keith.
by sandersk
Tue Oct 11, 2005 11:57 am
Forum: Operation
Topic: Tach cuts out at 3000rpm - MJLJ ver3
Replies: 2
Views: 3695

tach cutting out

The readings are as follows (taken with digital voltmeter on 20v dc scale) Tickover - 12.8v 1500rpm - 12.4v 2000rpm - 12.25v 2500rpm - 12.2v 2700rpm - 12.18v (this is the point when tach cuts out) I haven't taken detailed readings from old dizzy setup but was similar pattern but starting at around 1...
by sandersk
Mon Oct 10, 2005 8:22 pm
Forum: Operation
Topic: Tach cuts out at 3000rpm - MJLJ ver3
Replies: 2
Views: 3695

Tach cuts out at 3000rpm - MJLJ ver3

I'm running straight from the Tach output on new MJLJ Ver 3, works ok up to around 3000rpm then tach just cuts out. Thought I'd seen something similar on this forum before but can't find it. Does anyone have any suggestions for simple circuit to fix this? P.S. the voltage output from MJ Tach pin is ...
by sandersk
Tue Sep 27, 2005 7:35 pm
Forum: Operation
Topic: EDIS won't advance, buffer length error??
Replies: 8
Views: 7841

Success at last!!!!!!!

Got there in the end. Had a general poke around the solder joints of the SAW connector and R1 resistor (which had a little less solder than others) and all of a sudden advance was working, but then dropped back to 10deg. Dabbed a little dab-ette of solder on them and all now ok. I guess even Brent i...
by sandersk
Tue Sep 27, 2005 5:44 pm
Forum: Operation
Topic: problem with SAW signal
Replies: 7
Views: 7879

How did you fix your advance problem?

Hi guys,

I'm having the same problem, can you please tell me how you fixed it?

Keith S.
by sandersk
Tue Sep 27, 2005 4:51 pm
Forum: Operation
Topic: EDIS won't advance, buffer length error??
Replies: 8
Views: 7841

still no joy....

Have changed EDIS but still no advance seen on strobe. So in summary.... 1.Software runs ok with no error messages 2. Comms seem ok between PC and MJLJ - can read/update config and see "runtime" working correctly 3. Can see an a.c. voltage on the SAW wire at EDIS which increases as rpm ris...
by sandersk
Tue Sep 27, 2005 2:13 pm
Forum: Operation
Topic: EDIS won't advance, buffer length error??
Replies: 8
Views: 7841

Yes - Runtime shows correct rpm

Runtime looks correct so PIP must be ok, I do get a variable voltage on SAW that's not a million miles away from yours so I'll assume MJLJ is OK and source another EDIS and try that.

Thanks for your help - will let you know how I get on.

Regards,


Keith S.
by sandersk
Mon Sep 26, 2005 6:40 pm
Forum: Operation
Topic: EDIS won't advance, buffer length error??
Replies: 8
Views: 7841

Error message gone but still no advance on strobe

Matt, Thank you for your help, have loaded this and no more error messages. However, no matter what map I load the strobe still shows 10deg Have looked more closely at voltage coming out of MJ on saw pin (using digital voltmeter on 2v a.c. scale) - measures approx 0.05v at tickover and raises to app...