Search found 8 matches

by squirrelgripper
Sat Aug 07, 2004 8:16 am
Forum: Assembly
Topic: Testing Voltages During Assembly - Need A Little Help.
Replies: 8
Views: 8109

Testing Voltages During Assembly - Need A Little Help.

I am at the point in the assembly where I am testing voltages.

1. With a 9 volt battery, I am getting 5.8V - 6V for each of the tests.
2. With a 12 volt car battery, I am seeing 10V for each of the tests.

Is this correct?

Thanks,
Iain, Little Rock, AR
by squirrelgripper
Sun May 23, 2004 6:19 pm
Forum: Q&A
Topic: Crank Trigger Wheel
Replies: 8
Views: 15147

Here It Is

The part # I have is F2LZ-12A227-BB . http://www.squirrelgripper.netfirms.com/36tooth.jpg I believe this is the same as part # F2LE-12A227-BC I ordered mine online from www.oemparts4u.com - it was $US14.05 plus $US6.95 shipping = $21.00 - on the main menu "SEARCH BY OEM PART #",enter F2LZ1...
by squirrelgripper
Sat May 08, 2004 4:26 am
Forum: Installation
Topic: Trigger Wheel thickness
Replies: 7
Views: 9267

Barry (or others) - do you ha

Barry (or others) - do you have the part # / price for the Ford harmonic balancer? Is the trigger wheel hollow in the center, like in this thread? http://www.914club.com/bbs2/index.php?s=823036ca49bb4b0701c7297cdbdacad8&act=ST&f=2&t=9123 The reason I ask is that I ordered a trigger wheel...
by squirrelgripper
Wed May 05, 2004 3:11 am
Forum: Assembly
Topic: Zener Diode Backordered at Digikey - 6/11/2004!
Replies: 15
Views: 17748

Barry, I went to the Radio

Barry, I went to the RadioShack on Cantrell Rd looking for one - they were out of stock until Friday -have you cornered the market in Little Rock?! Also, Brent - as you mentioned in another post the problem is that the diode shipped by Digikey has the thicker leads - do you know any way of ordering ...
by squirrelgripper
Sat May 01, 2004 3:43 am
Forum: Assembly
Topic: 2 questions - D5 and the Molex connector
Replies: 9
Views: 9299

Edit: never mind, I've figure

Edit: never mind, I've figured the Molex connector out from the schematic - just to confirm - pin #1 is bottom left, pin #14 is top left as you look at the mating end of the connector, right?
by squirrelgripper
Sat May 01, 2004 3:40 am
Forum: Assembly
Topic: 2 questions - D5 and the Molex connector
Replies: 9
Views: 9299

2 questions - D5 and the Molex connector

Just got the board, I've started putting it together. A few questions: 1. D5 is as tight as the proverbial gnat's ass - should I drill it out with a 1/64" bit? I can't get the component to fit any other way. 2. To power up the board I need to supply 12V thru the Molex connector, right? I've loo...
by squirrelgripper
Sat May 01, 2004 1:02 am
Forum: Q&A
Topic: April 2, 2004: Are there any boards/processors available?
Replies: 22
Views: 23219

Thanks Brent!

The board and chip arrived today - I appreciate your honesty, Brent. Thanks!
by squirrelgripper
Fri Apr 02, 2004 6:40 pm
Forum: Q&A
Topic: April 2, 2004: Are there any boards/processors available?
Replies: 22
Views: 23219

April 2, 2004: Are there any boards/processors available?

Brent,

I ordered a board and processor yesterday via Paypal without thinking that you might have exhausted your supply. Do you have any currently in stock, and if not, when do you anticipate getting more?

Thanks,
Iain