Autosport Labs

Hi Jenko Fairly sure we met at the Hants and Wilts WSCC Dyno Shootout on Saturday at JKM Performance? I had the prisoner coloured seven with the extra low power :-) Managed to get some footage onto youtube http://www.youtube.com/watch?v=iUjE9kOptPc Going to go back there when I sort the fuelling out...

Ok the dyno shootout at JKM performance in Portsmouth happened and they kindly allowed me to flick the dual map switch for one of the runs All went well as far as sparks went and I think everyone was suitably impressed at the dual map switching stuff :-) I knew I should have hounded you for stickers...

OK Brent, had the unit out of the car to just give my soldering a once over and noticed the new dual map switch was a bit vague feeling and a bit sloppy Put a meter across it and sure enough it had gone vague internally if the unit was shaken Think I may have put a little too much heat into it when ...

I have a V2 board and am running the latest firmware - dual maps are working fine, but since the new firmware and dual maps have been loaded I'm getting a lot more false triggers (all shift lights blink) Noticed this higher up the rev range (did a bit of motorway driving with it today) Not sure if i...

All good mate , thank you very much!!! Great instructions and this numpty managed it without touching the wrong end of the soldering iron even once :-) Dual config works great so can switch between maps at the touch of a button The only query I have is I THINK the dialog box that prompts for reading...

Ok Cheers Brent,

I will keep an eye on the page..

I have a "Dyno shootout" booked for next week and have a switch and a mixed bag of components at the ready
I really want to beat the chaps still on clockwork dissys....no pressure though
________
Excursion

Yep their real nice chaps , and above all enthusiasts with a passion My manifold was a bit of a one off for them as I insisted on small ID tubes to suit my smaller choked carbs and specific angle of dangles etc I know they were geared up flanges for the ford heads, hopefully they will be able to sor...

Well if the stickers are worth 10hp each I'd better take a handfull and apply them liberally in time for our local dyno shootout

Seriously though Brent - are you going to pop them on the webstore for sale?
________
Holden Commodore

yep somewhere... Mine was built by knnmanifolds in exchange for me hosting their site :-) Closeup pics of my manifold and carbs on their site under the 'other' section http://www.knnmanifolds.co.uk/manifzr1.JPG http://www.knnmanifolds.co.uk/manifzr2.JPG Not sure if the above pics will appear..... if...

Brent, The link to .. "Download the MJLJ 2.7.x firmware image from the V2.x download area" from that page seems to point to the version 3XX stuff. (http://www.autosportlabs.net/MJLJ_V3_Downloads) Not that this is the case here... but I guess a few V2.xx users may get the wrong firmware /do...

TPS is definately where its at with bike carbs (esp as they already have one fitted) Mine all works very nicely - couldn't get hold of the original bike loom connector - but 3 minicrimps have been good for the past couple of thousand miles without falling off or any issues I'm using FZS 600? (think ...

wow!
what can I say?

Other than thanks Brent!
Your a star
________
Louisville Assembly Plant

Hi, I would like to try out dual maps on my v2 board Looking at the site it looks like there may be schematic about to be put under the upgrade instructions and I was going to hold back till it had been written ----------------------------------- QUOTE -------------------------------- 2.x MJLJ contr...

I'm not an expert but... Could be HT noise causing the rpm to be all over the place I suppose? Noise spikes caused me lots of niggling intermittent problems at first Changing plugs and leads for decent suppressed resitor type ones , checking that all connections and earths were clean and good seemed...

Can anyone please assist? I have wired in a simple set of LED's which work perfectly as shift lights - but I would like to add the extra function of getting them to flash when the soft rev limit is about to be hit I think I have found a way of doing this - but need assistance in choosing a suitable ...